Difference between revisions of "Capacitors"
| (One intermediate revision by the same user not shown) | |||
| Line 1: | Line 1: | ||
Capacitors hold a 'capacity' of electronics. You may want to take up [[Meditation]] if this is confusing. | Capacitors hold a 'capacity' of electronics. You may want to take up [[Meditation]] if this is confusing. | ||
| + | ==Capacitor Testing List== | ||
| + | There was a hackaday article on testing capacitors. It included steps such as looking at ESR, testing for a short, and a few other steps. I can't find it right now, but I'll leave this here, as the search engines may find it later. | ||
==Tips/Techniques== | ==Tips/Techniques== | ||
===AC Impedance=== | ===AC Impedance=== | ||
| Line 10: | Line 12: | ||
This has been discussed on the amp hour, referring to this article http://web.archive.org/web/20231208203302/https://www.signalintegrityjournal.com/articles/1589-the-myth-of-three-capacitor-values and if my memory isn't completely trashed, it came out to be: "most of the time you just throw a couple different values of caps on there and don't investigate unless necessary (but you should be aware of this trap)" or something like that. And that the signal integrity blog was 'technically correct' but for all practical purposes not correct (i.e. you won't have time to do a thorough analysis, although everything they wrote is true). I can't find the amp hour episode at the moment. Around 400. The impedance analyzer part (what you want) of the analog discovery is covered in detail here: https://digilent.com/reference/test-and-measurement/guides/waveforms-impedance-analyzer http://web.archive.org/web/20240303181454/https://wiki.digilent.com/reference/test-and-measurement/guides/waveforms-impedance-analyzer | This has been discussed on the amp hour, referring to this article http://web.archive.org/web/20231208203302/https://www.signalintegrityjournal.com/articles/1589-the-myth-of-three-capacitor-values and if my memory isn't completely trashed, it came out to be: "most of the time you just throw a couple different values of caps on there and don't investigate unless necessary (but you should be aware of this trap)" or something like that. And that the signal integrity blog was 'technically correct' but for all practical purposes not correct (i.e. you won't have time to do a thorough analysis, although everything they wrote is true). I can't find the amp hour episode at the moment. Around 400. The impedance analyzer part (what you want) of the analog discovery is covered in detail here: https://digilent.com/reference/test-and-measurement/guides/waveforms-impedance-analyzer http://web.archive.org/web/20240303181454/https://wiki.digilent.com/reference/test-and-measurement/guides/waveforms-impedance-analyzer | ||
| + | ===Ripple on Input/Output Capacitors=== | ||
| + | A given switcher may have an input and output capacitor. There are acceptable | ||
| + | values for input/output ripple (see [[Switchers#Calculators]]). This may be a hint | ||
| + | of the capacitor failing. | ||
[[Category:online notes]] | [[Category:online notes]] | ||
Revision as of 21:36, 19 April 2024
Capacitors hold a 'capacity' of electronics. You may want to take up Meditation if this is confusing.
Capacitor Testing List
There was a hackaday article on testing capacitors. It included steps such as looking at ESR, testing for a short, and a few other steps. I can't find it right now, but I'll leave this here, as the search engines may find it later.
Tips/Techniques
AC Impedance
I put an article about this in my book of hacks. At AC frequencies, certain caps (usually around 1uf or lower) start to get higher impedance. This can be a problem if you want to, e.g. pass audio across a DC blocking cap, but you choose a small ceramic as opposed to a 10uf electrolytic.
Resonant Frequencies of (input/output filter) Caps
Capacitance will differ based on the frequency. One reason why LCR meters have two different frequencies to test at. You can take it a step further though, and setup something like an analog discovery to do a full frequency vs. reactance characterization. See: https://tahmidmc.blogspot.com/2024/03/electrolytic-caps-over-frequency-why-is.html per Hackaday: https://hackaday.com/2024/04/01/why-is-my-470uf-electrolytic-cap-more-like-20uf/ http://web.archive.org/web/20240402042237/https://tahmidmc.blogspot.com/2024/03/electrolytic-caps-over-frequency-why-is.html This has been discussed on the amp hour, referring to this article http://web.archive.org/web/20231208203302/https://www.signalintegrityjournal.com/articles/1589-the-myth-of-three-capacitor-values and if my memory isn't completely trashed, it came out to be: "most of the time you just throw a couple different values of caps on there and don't investigate unless necessary (but you should be aware of this trap)" or something like that. And that the signal integrity blog was 'technically correct' but for all practical purposes not correct (i.e. you won't have time to do a thorough analysis, although everything they wrote is true). I can't find the amp hour episode at the moment. Around 400. The impedance analyzer part (what you want) of the analog discovery is covered in detail here: https://digilent.com/reference/test-and-measurement/guides/waveforms-impedance-analyzer http://web.archive.org/web/20240303181454/https://wiki.digilent.com/reference/test-and-measurement/guides/waveforms-impedance-analyzer
Ripple on Input/Output Capacitors
A given switcher may have an input and output capacitor. There are acceptable values for input/output ripple (see Switchers#Calculators). This may be a hint of the capacitor failing.
