Difference between revisions of "Wireguard"

From Steak Wiki
Jump to navigationJump to search
Line 64: Line 64:
 
note that the Alias may be different from wg0.
 
note that the Alias may be different from wg0.
 
the samba error in mount.cifs in linux (if testing an smb share) is
 
the samba error in mount.cifs in linux (if testing an smb share) is
mount error(115): Operation now in progress
+
mount error(115): Operation now in progress.
 
the smb error in windows. haha. there's no fucking error # in windows. just a
 
the smb error in windows. haha. there's no fucking error # in windows. just a
 
generic error message.
 
generic error message.

Revision as of 06:43, 30 December 2023

wireguard has a few setup scenarios. each are unique.


windows client to owrt split tunnel

windows

this setup assumes you are using it as a traditional vpn to access resources. not to hide your ip address / internet traffic.

download, run installer, add empty tunnel

[Interface]
PrivateKey = (it should auto populate this for you)(public key is above in text field)                          
Address = (the ip you want on the vpn net/32 for one ip)

[Peer]
PublicKey = (find it on server)
AllowedIPs = (what you want to be able to connect to on vpn lan)(usually its the vpn router's ip, and then the lan range behind the router)
Endpoint = (ipaddress:port)

Optional: If you have a windows server w/dns (i.e. domain) don't use the vpn router but the windows server as the DNS. However, you may want to also add some other dns (level 4 / google) as backups. e.g.

[Interface]
PrivateKey =                        
Address = 
DNS = (windows server and the subnet should be on allowed ips, if it isn't already), 4.2.2.2, 8.8.8.8

troubleshoot that with nslookup. You might think you can avoid this and hardcode the dns in window's /etc/hosts but that won't properly resolve the domain controller. and everytime you access a domain share you have to enter a password. bad idea.

owrt

config interface 'vpn'
        option proto 'wireguard'
        option private_key
        option listen_port someport
        list addresses ipofvpnhost

config wireguard_vpn 'anyname'
        list allowed_ips 'onlyoneip/32'
        option public_key
        option route_allowed_ips '1'

only tricky thing here is you need route_allowed_ips so the client knows to look for it's specified allowedips on the vpn iface the good news about this setup, is that owrt handles some of the routing / forwarding on its side. so you don't have to worry about a source nat command. you do have the follow the owrt install docs for wg though.

Tips/Troubleshooting

Basics

tcpdump -ni eth1 dst/src <ip>
tcpdump -ni vpn
route
wg (make sure the keys line up)

Make sure the vpn network is added to the lan section of /etc/config/firewall. This is a mistake I used to make.

Imagine doing this on one of those intern designed tacked on guis from sophos or sonicwall. Pure torture. Literally a layer of dogshit painted over the 'actually useful' command line tools. There is a reason starlink uses Owrt, and not some busywork web gui bullshit. Trying to use the molasses packet capture on a sonicwall or sophos through the web gui is demonic firewall design. "Some things exist on earth as an example of how it is 'not' supposed to be done".

Windows Firewall for SMB Shares

Windows and wireguard will set it as a public network where smb doesn't always work. the network is not listed in settings. but its there in the firewall section of settings... so you have to edit it via powershell. bad software design.

Get-NetConnectionProfile will list the networks (there are a bunch of windows Get- commands)
Set-NetConnectionProfile -InterfaceAlias 'wg0' -NetworkCategory 'Private'

note that the Alias may be different from wg0. the samba error in mount.cifs in linux (if testing an smb share) is mount error(115): Operation now in progress. the smb error in windows. haha. there's no fucking error # in windows. just a generic error message.

Finally, you have to make one other change: its a firewall error. as you can prove because mount.cifs works with the firewall disabled. Therefore, set these ports open:

UDP\137-138 and TCP\137,139,445.

in windows advanced firewall. it's two rules, so set all the TCP ports open, then all the UDP ports open

todo

alpine to owrt

debian to owrt

windows to windows

owrt to debian

CLIENT: openwrt
config interface 'vpn'
        option proto 'wireguard'
        option private_key '
        list addresses 'youraddress'

config wireguard_vpn
        option description 'name'
        option endpoint_host 'ipaddress'
        option endpoint_port 'port'
        list allowed_ips 'debiansubnetsyouwanttoaccess/24'
        list allowed_ips 'debianvpnaddress/32'
        option public_key '
        option preshared_key '
        option route_allowed_ips '1'

the allowed ips and route allowed ips are important here. if this was a fullon vpn, the allowed ips would be 0.0.0.0/0

SERVER: debian 10
====================
(etc network interfaces)
(note: see debian wiki for an alternative configuration)
auto wg-p2p
iface wg-p2p inet static
        address anyip
        netmask 255.255.255.0
        pre-up wg-quick up $IFACE
        post-down wg-quick down $IFACE

(/etc/wireguard/wg-p2p.conf)

[Interface]
PrivateKey = 
ListenPort = portnumber

[Peer]
PublicKey =
PreSharedKey = 
AllowedIPs = owrtvpn/32

with these two settings, the iface will be visible on the specified udp port 

and ping between will work. this is p2p.
if ping doesnt work, make sure there are routes between each box on the vpn interface

next

DEBIAN requires firewall rules
AND
ipv4 forwarding enabled.

its NOT masquerade
it's this:
iptables-legacy -t nat -A POSTROUTING -s vpnsubnet/24 -o vpsoutputiface -j SNAT --to-source vpswanip
the outputiface is eth0 or eth1
convert to nft with iptables-translate if necessary

in my VPS, ipv4 forwarding was not enabled by default. TRAP.
so do that right too.

vpns will bite you here:

firewall rules must change traffic from vpn to appear like its coming from vps. yes, even wireguard (sometimes... depends what distro you use)
forwarding must be enabled (depends upon distro again, but don't forget this)
wireguard: routes must be properly setup
wireguard: ping to start interface conversation from client. when in doubt use tcpdump.


firewall on client owrt: must add vpn to WAN (not lan zone) to minimize setup (i.e. so you don't make its own interface)
once you do this last step, clients will be able to connect in the client pool. not just the owrt router.

Troubleshooting:
make sure docker isn't causing trouble. if you install docker, it disables the 
default forwarding policy of accept. (makes it reject).