Difference between revisions of "TestEquipment"

From Steak Wiki
Jump to navigationJump to search
 
(27 intermediate revisions by the same user not shown)
Line 1: Line 1:
 
The goal is not to have all of the test equipment, or none, but to have the '''right''' test equipment.
 
The goal is not to have all of the test equipment, or none, but to have the '''right''' test equipment.
Footprint is important. Beware. "One man can only carry so many boat anchors".
+
 
 +
 
 +
Footprint is important. You will want to spend some time thinking about [[Storage]]. Try to get equipment that has a digital interface, so that you can automate your setup.
 +
 
 +
==Specific Equipment==
 +
===Curve Tracer===
 +
Don't buy one without GPIB/USB/Serial. Useless for documentation.
 +
===DVM===
 +
Density = Mass over Volume. Are you dumb?
 +
* https://www.eevblog.com/forum/projects/ppmgeek!-5-5-digit-dvm-volt-ref-cal-(for-arduino-or-any-uc-w-spi)/ - DIY 5.5 DVM. I haven't dug through this yet.
 +
===Load===
 +
Dummy load in a bucket of water (drum) with enameled wire
 +
(must be enameled to allow for the heat to dissipate, whereas plastic
 +
coated wire would melt the insulation first).
 +
* https://www.eevblog.com/forum/testgear/makeshift-load-bank/
 +
* https://youtu.be/WECW88rJYrE
 +
 
 +
===Oscilloscoop===
 +
===Spectrum Analyzers===
 +
There is the TinySA, similar in idea to the NanoVNA.
 +
* https://www.eevblog.com/forum/testgear/used-spectrum-analyzer-buyer_s-guide/
 +
* https://www.eevblog.com/forum/testgear/tinysa-ultra-launched/ - see this link for official tinysa resellers
 +
 
 +
===Vector Network Analyzers===
 +
* https://theamphour.com/533-microwave-measurement-with-joel-dunsmore/ Amp Hour 533 "Cables are Dogs". Dogs, and VNAs huh...? ... There is a book written by this fellow that would be worth reading if you are working with a VNA (Handbook of Microwave Component Measurements). As noted in the podcast, the first couple chapters are theory, the second section of the book is solving practical problems, and gives specific steps for a given scenario.
 +
* https://www.eevblog.com/forum/rf-microwave/inexpensive-cal-standards/ - Notes on cals for VNAs.
 +
* https://www.eevblog.com/forum/rf-microwave/how-to-measure-vswr-of-tiny-antennas-how-to-eliminate-effect-of-vna-cables/ - calibrating with antennas
 +
* https://www.eevblog.com/forum/testgear/banggood-50-ohm-bnc-feed-through-terminator-a-quick-review/50/ - 50 ohm terminator deep dive. Considering parasitic effects (i.e. when a component's package inherent capacitance or inductance starts to affect the circuit at high frequency).
  
 
==Tips/Techniques==
 
==Tips/Techniques==
 +
===Consider Digital Interfaces for All Equipment===
 +
If you want to get serious work done, you are probably going to want to script or automate your setup. So beware of old Bench DMMs, function gens, and other equipment that doesn't have at least a GPIB interface.
 
===Output of equipment at 0 Volts===
 
===Output of equipment at 0 Volts===
  
https://www.eevblog.com/forum/testgear/itech-it6121-precision-power-supply-always-display-a-tiny-reading/msg5424086/#msg5424086
+
* https://www.eevblog.com/forum/testgear/itech-it6121-precision-power-supply-always-display-a-tiny-reading/msg5424086/#msg5424086 Equipment is not guaranteed to output 0 volts, unless specified.
  
 
===Try to Support Local Businesses===
 
===Try to Support Local Businesses===
 
If there is a vendor of a tool or TE near you, then buy from them.
 
If there is a vendor of a tool or TE near you, then buy from them.
 
[[Category:online notes]]
 
[[Category:online notes]]
 +
===Automation===
 +
* https://www.eevblog.com/forum/rf-microwave/rf-test-automation-423998 rhode & scwharz has
 +
some resources. not sure if these links are very useful though. double check.
 +
 +
==External Links==
 +
* https://w140.com/tekwiki/wiki/Main_Page The Tek Wiki, is actually quite well done.
 +
buying equipment? see below. a nice image gallery of compatible hardware with sigrok
 +
* https://sigrok.org/wiki/Supported_hardware

Latest revision as of 22:54, 29 April 2024

The goal is not to have all of the test equipment, or none, but to have the right test equipment.


Footprint is important. You will want to spend some time thinking about Storage. Try to get equipment that has a digital interface, so that you can automate your setup.

Specific Equipment

Curve Tracer

Don't buy one without GPIB/USB/Serial. Useless for documentation.

DVM

Density = Mass over Volume. Are you dumb?

Load

Dummy load in a bucket of water (drum) with enameled wire (must be enameled to allow for the heat to dissipate, whereas plastic coated wire would melt the insulation first).

Oscilloscoop

Spectrum Analyzers

There is the TinySA, similar in idea to the NanoVNA.

Vector Network Analyzers

Tips/Techniques

Consider Digital Interfaces for All Equipment

If you want to get serious work done, you are probably going to want to script or automate your setup. So beware of old Bench DMMs, function gens, and other equipment that doesn't have at least a GPIB interface.

Output of equipment at 0 Volts

Try to Support Local Businesses

If there is a vendor of a tool or TE near you, then buy from them.

Automation

some resources. not sure if these links are very useful though. double check.

External Links

buying equipment? see below. a nice image gallery of compatible hardware with sigrok